linerwisdom.blogg.se - Rockshox xloc instructions

#ROCKSHOX XLOC INSTRUCTIONS FULL#
#ROCKSHOX XLOC INSTRUCTIONS PROFESSIONAL#
#ROCKSHOX XLOC INSTRUCTIONS FREE#

The competitor is a professional supplier with headquarters in the Euro-Zone. The product is readily available at the competitor. The product is the same (size, colour, model year, finish etc.) as ordered. The price difference per product is €1 or more.

Wipe off any remaining oil from the remote and post and return the remote and post to the riders desired position.If you find an item at a lower price with another commercial internet retailer, you will receive it from us at the same price, provided the conditions listed in the link are met.

Function test the system to ensure successful operation.

Unthread the syringe and ensure there is a pool of oil in the bleed port.

Press the syringe and allow the plunger to return on its own. Push on the syringe and feel the remote lever become solid.

#ROCKSHOX XLOC INSTRUCTIONS FULL#

Unscrew the post or crown bleed screw and thread in a ½ full syringe.

If the lever does then there may well be air still in the system.

If the system has been correctly bled then the remote lever should be solid to the press and not extend when pulled.

Unthread the syringe and replace the bleed screw.

Give the remote syringe a final press and let the plunger pop back up on its own.

This should dislodge any remaining air bubbles in the remote.

Press down on the remote syringe to ensure the lever is fully extended and then push the lever whilst gently pulling on the syringe.

Remove the crown or post syringe and thread in the bleed screw.

Balance both syringes so they are ½ full.

#ROCKSHOX XLOC INSTRUCTIONS FREE#

If the oil is severly discoloured you will need to remove the syringes, dispose of the old fluid and refill and repeat the process until the oil runs clear and free of air in both syringes. Continue until no more air bubbles emerge from the system. You will find pressing gently on one syringe whilst pulling gently on the other syringe achieves the best results. Cycle the oil between the two syringes.

Remove the bleed screw on the remote and thread in the ¼ full syringe.Remove the bleed screw on the post or crown lockout and thread in the ¾ full syringe.Fill one syringe ¾ full of Reverb oil and the other a ¼ full.The instructions will tell you to turn the adjuster so that it is woundįully out giving maximum volume to the remote (in the direction of the arrow for the XLoc – in the opposite direction of the arrow for the Reverb) we have found some good results by winding the adjuster all the way in (the reverse to what the instructions say) If by following the instructions you find the post only to extend in theįully fast position and be locked solid in the full slow position, then repeat the procedure with the adjuster in full fast (Reverb).Reverb remotes should naturally rest in this position. On the XLoc remotes it’s important that the lever is in the fully extended position.Use a T25 Torx key to position the remote so that the bleed screw is slightly higher above the lever.XLoc remotes will naturally be higher than the lever bleed screw. If the Reverb is an external type, then move the clamp to position the remote higher than the bleed screw. If you can, lower the workstand to hold the post. Make sure the bike is supported throughout the procedure. You will need to remove a Reverb Stealth dropper to access the bleed screw.Tools required: Safety glasses, Nitrile gloves, Reverb bleed syringes, T10 and T25 Torx keys, Rockshox Reverb oil (or 3wt) Blue cloth and a drip tray. The remote bleed process is basic, but there are a few extra tips we’ve found that can assist the procedure. There are a few different types of the Rockshox hydraulic remote lever, the ones with gold adjusters are the XLoc type used on the fork and rear shock lockouts and the black (or silver) adjuster types are the speed adjusters used on the Reverb dropper post. There can be a number of reasons why a Rockshox Reverb dropper post or fork lockout can stop working, but the most basic reason is air in the remote and hose.